It’s soon time to Winterize

This post was written by Wendy on October 11, 2017
Posted Under: Uncategorized

We all hate to let go of the handlebars and try to squeak out as many fall rides as we can before the dreaded snow & ice is upon us. That’s just human nature, but you can start thinking about getting ready for that day when the temps are down & snow is in the forecast.  You want to protect your investment and be on the road next spring with no hassle….so you’ve got to take the plunge and follow the Ten Simple Steps to Winterize Your Motorcycle:

 1) Surface Prep

Washing your bike when nobody will see it for a few months anyway can be a drag, but giving your bike a thorough cleaning before storage is important; letting bug guts or water spots sit on your paint can corrode the finish permanently. Wash your bike and dry it completely to get all the moisture off the surfaces (an electric leaf blower is a great way to get all the nooks and crannies really dry.)

Add a coat of wax, which will act as a barrier against moisture and rust. Finally, spray exposed metal surface with WD-40 to displace all moisture and give them a protective coating against corrosion.

2) Change the Oil and Filter

Change your oil and filter. It’s better for your lubrication system to have fresh oil sitting in it for several months than to have used, broken down oil in it. The last thing you’ll want to do when riding season begins is change the oil before you can go ride. Using a winter weight oil like 5W30 can help it start up easier come spring time as well.

If you’re going to be storing your bike for a long time (4-6 months or more) you will want to protect your engine’s internals against moisture by coating them lightly with oil. You may not be able to see it with your naked eye, but the cold winter air is perfect for moisture to gather in your engine and cause rust to form on your pistons and cylinder walls.

Remove the spark plugs and put a little squirt (about a tablespoon) of engine oil into the holes, then turn your engine over a few times to coat the cylinder walls by spinning the rear wheel with the bike in gear. Once everything is coated, replace the spark plugs.

3) Lube Moving Parts

Keeping moving parts lubed during the winter helps to keep moisture from building up on them and causing any rusting or binding. Any part of your motorcycle that needs to be lubed at any point should be lubed again before storage. Some parts to check are: chain drive, cables, controls, fork surfaces, and any other pivot points.

4) Prep Fuel System

Gas tanks have a tendency to rust when not in use, and untreated pump gas breaks down and becomes gummy over time. To prevent rusting and make sure your fuel is ready to run after a few months in storage, you’ll want to fill your tank completely with fuel treated with a fuel stabilizer.

On your last ride of the season, stop in at the gas station nearest to where you will be storing your bike and add the proper amount of fuel stabilizer, then top off the tank. A full tank will keep moisture from building up on the tank walls, and adding the stabilizer before the short ride home will help mix the gas and stabilizer together and run it through your fuel system before storage.

5) Safeguard the Battery

Batteries have a tendency to self-discharge when sitting over time, especially when they remain hooked up to the bike. The easiest way to combat this is to hook up a battery tender to monitor the charge and keep the battery topped off without overcharging. Normally you should pull the battery from the bike for storage, but with a smart tender you can also connect the tender with the battery left in the bike. Before doing this, make sure the electrodes are clean and corrosion free; if necessary, clean them off and give them a light coating of grease.

6) Protect your Tires

If your tires are left to sit in the same position all winter long, they could develop flat spots. Keeping the tires off of the ground will prevent this, so if you have motorcycle stands put the bike up on them for storage. If you don’t have stands, try to get at least the rear tire off the ground, or you can rotate your tires by rolling your motorcycle slightly every few weeks. If you need to leave your tires down on concrete, put a piece of carpet or plywood under them to keep any moisture from seeping into them.

7) Check Coolant/Anti-freeze

If you’ll be storing your bike somewhere that gets below freezing, make sure you have adequate levels  of anti-freeze in your coolant system. This is very important; if your coolant system freezes, you could come back to a cracked head in the spring!

8) Plug Out Pests

Mice and other rodents are notorious for hiding from the cold inside exhaust pipes and making homes out of air filters. If order to avoid any furry surprises when it’s time to ride again, plug up your pipes with an exhaust plug  or you can also simply stuff your air intake and the ends of your exhaust with some plastic bags – but do use bright colored bags or tie something to them so you don’t forget take them out when you fire up the bike!

9) Keep it Covered

With your motorcycle fully prepped for winter,  a quality motorcycle cover will not only keep dust off the bike, but will keep the moisture out so it doesn’t get trapped underneath it, and create corrosion or rust. If you’re storing it outside, be sure to get a cover with tie downs to prevent it from blowing loose in wind. If you’re storing it inside you’re in much better shape, but you should still use a cover to prevent dust from building up on it.

10) Theft Protection

If you’re storing your bike outside, bear in mind that being parked unattended for months at a time makes it an easy target for theft. In addition to protecting your bike from weather, using a cover will conceal it from view, and securing it with a heavy lock and chain can give you some peace of mind. If you are storing your bike anywhere it can be accessed by others,  consider investing in some security measures.

Add a Comment

required, use real name
required, will not be published
optional, your blog address